EUROLAB
en-1426-bitumen-and-bituminous-binders-determination-of-needle-penetration
Asphalt and Bitumen Testing AASHTO T240 Viscosity Determination of Asphalt Binder Using the Vacuum Capillary ViscometerAASHTO T279 Determining the Dynamic Modulus and Flow Number for Asphalt MixturesAASHTO T313 Determining the Asphalt Binder Content of Hot Mix AsphaltAASHTO T313 Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA)AASHTO T40 Sampling and Testing Bituminous MaterialsAASHTO T49 Determining the Softening Point of Bitumen (Ring-and-Ball Apparatus)AASHTO T59 Determining the Emulsion Content of Bituminous EmulsionsAASHTO T72 Sampling Bituminous MaterialsASTM D113 Ductility of Bituminous MaterialsASTM D1754 Standard Test Method for Emulsified AsphaltASTM D1856 Effect of Heat and Air on a Moving Film of Asphalt (Rolling Thin-Film Oven Test)ASTM D217 Penetration of Bituminous MaterialsASTM D2172 Quantitative Extraction of Bitumen from Bituminous Paving MixturesASTM D2489 Standard Practice for Estimating the Surface Area of AggregateASTM D2726 Bulk Specific Gravity of Compacted Bituminous Mixtures Using Saturated Surface-Dry SpecimensASTM D2950 Density of Bituminous Concrete in Place by Nuclear MethodsASTM D36 Softening Point of Bitumen (Ring-and-Ball Apparatus)ASTM D4124 Quantitative Separation of Asphalt Binder from Aggregate Using a Centrifuge Extraction MethodASTM D4402 Viscosity Determination of Asphalt at Elevated TemperaturesASTM D4867 Effect of Heat and Air on Asphalt Binder Using Thin Film Oven Test (TFOT)ASTM D4957 Preparation of Bituminous Specimens Using Marshall ApparatusASTM D5141 Bulk Specific Gravity of Compacted Bituminous Mixtures Using the Immersed MethodASTM D5444 Bulk Specific Gravity of Compacted Asphalt Mixtures Using Saturated Surface-Dry SpecimensASTM D5492 Standard Practice for Accelerated Aging of Asphalt Binder Using a Pressurized Aging Vessel (PAV)ASTM D5870 Standard Practice for Accelerated Aging of Asphalt Binder Using a Pressurized Aging Vessel (PAV)ASTM D5890 Determining the Rutting Susceptibility of Asphalt Binders Using a Dynamic Shear RheometerASTM D6114 Determination of Asphalt Binder Yield and Volumetric PropertiesASTM D6307 Standard Test Method for Asphalt Binder Content of Hot Mix Asphalt Using the Ignition MethodASTM D6601 Determining Rheological Properties of Asphalt Binder Using a Dynamic Shear RheometerASTM D6601 Standard Test Method for Determining Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR)ASTM D6693 Determination of Tensile Strength and Tensile Creep Using the Asphalt Binder Cracking DeviceASTM D6926 Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR)ASTM D6997 Standard Test Method for Bulk Specific Gravity of Compacted Asphalt Mixtures Using the Immersed MethodASTM D70 Specific Gravity and Density of Semi-Solid and Solid Bituminous MaterialsASTM D7405 Determining the Fatigue Life of Asphalt Binders Using the Linear Amplitude Sweep TestASTM D92 Flash and Fire Points by Cleveland Open Cup TesterBS EN 12594 Bitumen and Bituminous Binders - Sampling and Preparation of Test SamplesBS EN 13179-1 Bituminous Mixes - Test Methods for Hot Mix Asphalt - Part 1: SamplingEN 12591 Bitumen and Bituminous Binders - Specifications for Paving Grade BitumenEN 12607 Bitumen and Bituminous Binders - Determination of the Resistance to HardeningEN 12697-12 Bituminous Mixtures - Test Methods for Hot Mix Asphalt - Part 12: Determination of the Water Sensitivity of Bituminous SpecimensEN 12697-26 Bituminous Mixtures - Test Methods for Hot Mix Asphalt - Part 26: StiffnessEN 13036-1 Road Materials - Test Methods - Part 1: Sampling and Sample PreparationEN 1427 Bitumen and Bituminous Binders - Determination of Softening Point - Ring and Ball MethodEN 1428 Bitumen and Bituminous Binders - Determination of Density and Bulk DensityISO 11357-3 Plastics - Differential Scanning Calorimetry (DSC)ISO 3015 Bitumen and Bituminous Binders - Determination of DuctilityISO 4625 Bitumen and Bituminous Binders - Determination of Softening PointISO 6615 Bitumen and Bituminous Binders - Determination of Flash and Fire Points

EN 1426 Bitumen and Bituminous Binders - Determination of Needle Penetration Laboratory Testing Service Provided by Eurolab

Standard-Related Information

The EN 1426 standard is a European Standard that specifies the method for determining the needle penetration of bitumen and bituminous binders. This test is essential in assessing the performance and quality of bituminous materials used in road construction, paving, and other applications.

Relevant Standards

  • ISO (International Organization for Standardization) 3015:2000 - Bitumens - Determination of needle penetration
  • ASTM D5-11:2011 - Standard Test Method for Penetration of Bituminous Materials
  • EN 1426:2017 - Bitumen and bituminous binders - Determination of needle penetration
  • International and National Standards

    The international standard ISO 3015 is the basis for the European Standard EN 1426. The ASTM D5-11 standard is equivalent to the EN 1426 standard.

    Standard Development Organizations

  • ISO (International Organization for Standardization)
  • CEN (European Committee for Standardization)
  • ASTM International
  • Evolution and Update of Standards

    Standards evolve over time as new technologies, methods, and materials emerge. The EN 1426 standard was last updated in 2017 to reflect changes in test procedures and equipment.

    Scope and Application

    The EN 1426 standard applies to bitumen and bituminous binders used in road construction, paving, and other applications. It is essential for assessing the performance and quality of these materials.

    Compliance Requirements

    Industry sectors requiring compliance with this testing service include:

  • Road construction and maintenance
  • Paving and asphalt industries
  • Building construction and civil engineering
  • Consequences of Non-Compliance

    Failure to comply with EN 1426 standard requirements can result in reduced product quality, decreased performance, and increased risks.

    Test Conditions and Methodology

    The EN 1426 test involves the following steps:

    1. Sample Preparation: The bitumen or bituminous binder sample is prepared for testing.

    2. Testing Equipment: A needle penetration apparatus is used to measure the penetration of the bitumen or bituminous binder.

    3. Testing Parameters: The test is conducted at a temperature range of 25C 0.5C, and the penetration is measured using a needle with a diameter of 1/16 inch (1.59 mm).

    4. Measurement and Analysis: The penetration value is recorded and calculated.

    Quality Control and Assurance

  • Calibration and validation of testing equipment
  • Quality control measures during testing
  • Data collection and recording procedures
  • Reporting and Documentation

    Test results are documented and reported in accordance with the EN 1426 standard requirements.

    Why This Test Should Be Performed

    This test is essential for:

    1. Quality Assurance: Ensures product quality and performance.

    2. Regulatory Compliance: Meets industry sector compliance requirements.

    3. Risk Assessment: Mitigates risks associated with product performance.

    4. Competitive Advantages: Enhances market positioning and customer trust.

    Why Eurolab Should Provide This Service

    Eurolab offers:

    1. Expertise and Experience: State-of-the-art equipment and facilities, qualified personnel.

    2. Accreditation and Certification: International recognition and partnerships.

    3. Quality Management Systems: Efficient turnaround time, competitive pricing.

    4. Technical Support and Consultation Services: Innovative solutions for customers.

    Eurolabs Capabilities

  • Expertise in bitumen and bituminous binders testing
  • State-of-the-art equipment and facilities
  • Qualified and certified personnel
  • Accreditation and certification details
  • Customer Testimonials

    Eurolabs services have been instrumental in ensuring our product quality and regulatory compliance. - XYZ Industry Ltd.

    We were impressed by Eurolabs efficiency, expertise, and competitive pricing. - ABC Engineering Inc.

    Addressing Customer Concerns

    We understand the importance of confidentiality, data protection, and reporting standards. Our dedicated customer service team is available to address any concerns or questions you may have.

    This comprehensive guide has provided detailed information about the EN 1426 bitumen and bituminous binders testing service offered by Eurolab. We hope this article serves as a valuable resource for industry professionals seeking authoritative insights into this laboratory testing service.

    Need help or have a question?
    Contact us for prompt assistance and solutions.

    Latest News

    View all

    JOIN US
    Want to make a difference?

    Careers