EUROLAB
astm-c469-static-modulus-of-elasticity-and-poissons-ratio-of-concrete-in-compression
Concrete and Mortar Testing AASHTO T112 Density of AggregateAASHTO T119 Compressive Strength of CylindersAASHTO T119 Compressive Strength of CylindersAASHTO T119 Compressive Strength of Cylindrical Concrete SpecimensAASHTO T161 Length Change of Hardened ConcreteAASHTO T22 Slump Test for Fresh ConcreteAASHTO T23 Air Content of Freshly Mixed Concrete by Pressure MethodAASHTO T24 Air Content of Hydraulic Cement Concrete by Pressure MethodAASHTO T71 Sampling and Testing of AggregateAASHTO T97 Compression Testing of ConcreteAASHTO T97 Compressive Strength of CylindersACI 209 Prediction of Creep, Shrinkage, and Temperature EffectsACI 211 Guide for Concrete Mixture ProportioningACI 214 Guide for Evaluation of Strength Test ResultsACI 234 Guide for Concrete DurabilityACI 301 Specifications for Structural ConcreteACI 318 Building Code Requirements for Structural ConcreteACI 318 Structural Concrete Code RequirementsACI 522 Guide for Fiber-Reinforced ConcreteACI 544 Fiber Reinforcement TestingASTM C1064 Temperature of Freshly Mixed Hydraulic-Cement ConcreteASTM C1074 Estimating Concrete Strength by Maturity MethodASTM C1077 Standard Practice for Laboratories Testing ConcreteASTM C109 Compressive Strength of Hydraulic Cement MortarsASTM C109M Compressive Strength of Hydraulic Cement MortarsASTM C114 Chemical Analysis of Hydraulic CementASTM C1152 Acid Soluble Chloride in Concrete and Concrete Raw MaterialsASTM C1157 Performance Specification for Hydraulic CementASTM C1202 Electrical Indication of Concrete’s Ability to Resist Chloride Ion PenetrationASTM C1231 Structural Testing of Drilled Concrete CoresASTM C1237 Flow of Mortar Using a Flow TableASTM C1240 Testing for Air-Entraining AdmixturesASTM C1260 Accelerated Mortar Bar Test for Alkali-Silica ReactionASTM C138 Unit Weight, Yield, and Air Content of ConcreteASTM C140 Density, Yield, and Air Content of MortarASTM C143 Slump of Hydraulic-Cement ConcreteASTM C143 Slump of Hydraulic-Cement ConcreteASTM C1512 Restrained Expansion of Mortar Bars Due to ASRASTM C156 Air Content in Freshly Mixed Concrete by Volumetric MethodASTM C157 Length Change of Hardened ConcreteASTM C157 Length Change of Hardened ConcreteASTM C1576 Testing Mortars for Air ContentASTM C1579 Early Age Shrinkage of Cementitious Mixtures Using Embedded Strain GaugesASTM C1585 Measurement of Rate of Absorption of Water by Hydraulic Cement ConcreteASTM C1602 Mixing Water for ConcreteASTM C1609 Flexural Performance of Fiber-Reinforced ConcreteASTM C1679 Method for Measuring Early-Age Shrinkage of Cementitious MixturesASTM C171 Sampling Fresh ConcreteASTM C185 Determination of Carbonation DepthASTM C185 Determination of Carbonation Depth in ConcreteASTM C185 Measurement of Setting Time of Hydraulic CementASTM C231 Air Content in Freshly Mixed Concrete by Pressure MethodASTM C231 Air Content of Freshly Mixed Concrete by Pressure MethodASTM C266 Time of Setting of Concrete Mixtures by Penetration ResistanceASTM C293 Flexural Strength of ConcreteASTM C293 Flexural Strength of Concrete Using Simple Beam with Third-Point LoadingASTM C293 Flexural Strength of Concrete Using Simple Beam with Third-Point LoadingASTM C293 Testing Concrete Beam Flexural StrengthASTM C31 Making and Curing Concrete Test SpecimensASTM C349 Compressive Strength of Hydraulic Cement MortarsASTM C39 Compressive Strength Testing of Concrete CylindersASTM C42 Obtaining and Testing Drilled Cores and Sawed BeamsASTM C469 Modulus of Elasticity and Poisson’s Ratio in ConcreteASTM C494 Chemical Admixtures for ConcreteASTM C642 Density, Absorption, and Voids in Hardened ConcreteASTM C666 Resistance of Concrete to Rapid Freezing and ThawingASTM C78 Flexural Strength of ConcreteASTM C78 Flexural Strength of Concrete BeamsASTM C805 Rebound Number of Hardened ConcreteASTM C876 Half-Cell Potential of Steel in ConcreteBS 1881-121 Determination of Water Absorption of Hardened ConcreteBS 1881-203 Testing for Compressive StrengthBS 1881-208 Testing for Flexural StrengthBS 4550 Specification for Concrete TestingBS 4551 Testing of Concrete – Methods for Strength and DensityBS 812 Testing AggregatesBS 8500-1 Concrete – Part 1: Specification for Constituent MaterialsBS 8500-2 Concrete – Part 2: Specification for ConcreteBS EN 1015-11 Determination of Flexural and Compressive Strength of MortarBS EN 197-1 Cement StandardsBS EN 206 Specification for ConcreteBS EN 480-11 Admixtures for Concrete – Testing MethodsBS EN 934-2 Concrete AdmixturesEN 12390-10 Determination of Chloride Content in Hardened ConcreteEN 12390-2 Making and Curing Specimens for Strength TestsEN 12390-3 Compressive Strength of Test SpecimensEN 12390-5 Flexural Strength of Test SpecimensEN 12390-6 Tensile Splitting Strength of Test SpecimensEN 12390-7 Density of Hardened ConcreteEN 12390-8 Depth of Penetration of Water Under PressureEN 12620 Aggregates for ConcreteEN 12620 Aggregates for ConcreteEN 13039 Siliceous Sand for ConcreteEN 13055 Lightweight AggregatesEN 13286-47 Test Methods for Unbound and Hydraulically Bound MixturesEN 13670 Execution of Concrete StructuresEN 196-1 Determination of StrengthEN 196-3 Determination of Setting Times and SoundnessEN 196-6 Determination of FinenessEN 197-1 Cement Composition and SpecificationsEN 197-1 Composition, Specifications and Conformity Criteria for Common CementsEN 206-1 Concrete Specification, Performance, Production and ConformityISO 14001 Environmental Management in Concrete ProductionISO 15686-2 Service Life Planning of Concrete StructuresISO 1920-1 Sampling of Hardened ConcreteISO 1920-3 Sampling Fresh ConcreteISO 1920-4 Strength Testing of Concrete – Part 4: Strength by CompressionISO 1920-5 Determination of Tensile Splitting StrengthISO 1920-6 Flexural Strength Testing of ConcreteISO 1920-7 Determination of Density of Hardened ConcreteISO 1920-8 Determination of Water Absorption of Hardened ConcreteISO 1920-9 Determination of Freeze-Thaw ResistanceISO 21930 Sustainability in Building ConstructionISO 22112 Concrete Testing – Durability TestingISO 679 Determination of Strength of Hydraulic CementISO 679 Methods of Testing Cement – Determination of Strength

ASTM C469 Static Modulus of Elasticity and Poissons Ratio of Concrete in Compression Laboratory Testing Service

Provided by Eurolab: Quality Assurance and Compliance

Table of Contents

1. Standard-Related Information

2. Standard Requirements and Needs

3. Test Conditions and Methodology

4. Test Reporting and Documentation

5. Why This Test Should Be Performed

6. Why Eurolab Should Provide This Service

ASTM C469 is a widely recognized standard for determining the static modulus of elasticity and Poissons ratio of concrete in compression. The standard is published by the American Society for Testing and Materials (ASTM) and provides guidelines for conducting this critical test.

Legal and Regulatory Framework

The testing service provided by Eurolab is governed by various international and national standards, including:

  • ISO 6784:2013 - Concrete, aggregates and concrete aggregate - Determination of static modulus of elasticity

  • ASTM C469-16 - Standard Test Methods for Static Modulus of Elasticity and Poissons Ratio of Concrete in Compression

  • EN 12390-12:2009 - Testing hardened concrete - Part 12: Determination of static elastic deformation

    • These standards ensure that the testing service meets the required quality, accuracy, and safety standards.

    Standard Development Organizations

    The development of ASTM C469 is a collaborative effort between various standard development organizations, including:

  • American Society for Testing and Materials (ASTM)

  • International Organization for Standardization (ISO)

  • European Committee for Standardization (CEN)

    • These organizations work together to ensure that the testing service meets international standards and best practices.

    Evolution of Standards

    Standards evolve over time as new technologies and methods emerge. The development of ASTM C469 has involved several revisions, with the latest revision being in 2016.

    Specific Standard Numbers and Scope

    The following are specific standard numbers and their scope:

  • ISO 6784:2013 - Determination of static modulus of elasticity

    • Scope: This International Standard specifies a method for determining the static modulus of elasticity of concrete.

  • ASTM C469-16 - Standard Test Methods for Static Modulus of Elasticity and Poissons Ratio of Concrete in Compression

    • Scope: These test methods cover procedures for determining the static elastic properties of concrete, including the modulus of elasticity and Poissons ratio.

    Industry-Specific Compliance Requirements

    Different industries have specific compliance requirements for ASTM C469 testing. For example:

  • Construction industry - Must comply with EN 12390-12:2009

  • Infrastructure industry - Must comply with ASTM C469-16

    • Compliance with these standards ensures that the testing service meets the required quality and safety standards.

    ASTM C469 is a critical test for determining the static modulus of elasticity and Poissons ratio of concrete in compression. The following are reasons why this test is needed and required:

    Business and Technical Reasons for Conducting ASTM C469 Testing

    The static modulus of elasticity and Poissons ratio of concrete in compression are critical properties that determine the behavior of concrete under load. This test provides valuable information for:

  • Structural design

  • Material selection

  • Quality control

  • Safety assessment

    • Consequences of Not Performing This Test

    Failure to conduct ASTM C469 testing can result in:

  • Inaccurate structural designs

  • Suboptimal material selection

  • Reduced quality and safety standards

  • Increased risk of failure or damage

    • Industries and Sectors Requiring This Testing

    The following industries and sectors require ASTM C469 testing:

  • Construction industry

  • Infrastructure industry

  • Building materials industry

    • These industries require this testing to ensure that their products meet the required quality, safety, and performance standards.

    ASTM C469 testing involves a series of steps to determine the static modulus of elasticity and Poissons ratio of concrete in compression. The following are detailed step-by-step explanations:

    Testing Equipment and Instruments Used

    The following equipment and instruments are used for ASTM C469 testing:

  • Compression testing machine

  • Displacement transducer

  • Strain gauge

  • Data acquisition system

    • Testing Environment Requirements

    The testing environment must meet the following requirements:

  • Temperature: 20C 5C

  • Humidity: 60 10

  • Pressure: Atmospheric pressure

    • Sample Preparation Procedures

    Concrete samples are prepared according to ASTM C469-16. The samples are cast, cured, and tested under standardized conditions.

    Testing Parameters and Conditions

    The following testing parameters and conditions apply:

  • Loading rate: 0.5 MPa/s

  • Displacement measurement: 1 mm

  • Strain measurement: 10 μm/m

    • Data Acquisition and Analysis

    Data is acquired using a data acquisition system, which records the load-displacement relationship. The data is then analyzed to determine the static modulus of elasticity and Poissons ratio.

    ASTM C469 testing results are reported in accordance with ASTM C469-16. The following information is included:

  • Test specimen details

  • Testing conditions

  • Test results

  • Calculations

    • Report Format

    The test report format must include the following sections:

  • Introduction

  • Materials and equipment used

  • Testing procedure

  • Results and discussion

  • Conclusion

    • Record Keeping

    Records of testing are maintained in accordance with ASTM C469-16. These records provide a permanent record of the testing history.

    ASTM C469 is a critical test for determining the static modulus of elasticity and Poissons ratio of concrete in compression. The following are reasons why this test should be performed:

    Structural Design and Material Selection

    ASTM C469 provides valuable information for structural design and material selection.

  • Accurate estimates of concrete properties

  • Optimal material selection

    • Quality Control and Safety Assessment

    ASTM C469 testing ensures that concrete products meet the required quality and safety standards.

  • Reduced risk of failure or damage

  • Improved product performance

    • Eurolab is a leading provider of ASTM C469 testing services. The following are reasons why Eurolab should provide this service:

    Expertise and Experience

    Eurolab has extensive expertise and experience in conducting ASTM C469 testing.

  • Highly skilled personnel

  • State-of-the-art equipment and facilities

    • Quality Assurance and Compliance

    Eurolab ensures that all testing is conducted in accordance with international standards, including ISO 6784:2013 and ASTM C469-16.

  • High-quality results

  • Accurate reporting and documentation

    • By choosing Eurolab for your ASTM C469 testing needs, you can ensure that your products meet the required quality, safety, and performance standards. Contact us today to learn more about our services!

    Need help or have a question?
    Contact us for prompt assistance and solutions.

    CONTACT US +902127020000

    Latest News

    View all

    Eurolab Successfully Renews ISO 17025 Accreditation

    Read More

    Expanded Cosmetic Safety Testing Portfolio Now Available at Eurolab

    Read More

    Eurolab Launches Technical Training Series for Industry Professionals

    Read More

    JOIN US
    Want to make a difference?

    Careers